Right here in the next paragraph you can find lots of really good guidance about Installing A Bathtub.
Setting up a tub isn't exactly brain surgery, yet it does call for strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old tub with a new one is also a moderately tough task. If the old bathtub is readily available, the task can move easily; if you have to open a wall to eliminate the old tub and also place the new bathtub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub and embeded in the new one. Make sure you have actually qualified on your own for the task and fit attempting it. Instead of hiring a contractor to take control of a halfway-completed job, it is far better to consider utilizing one before you begin. Opportunities are you may require a professional plumber to make tube links.
This article will aid you install a brand-new bathtub in your shower room if you have actually already purchased a brand-new bathtub and do not need to transform the setup of your previous water system pipelines.
Your tools as well as material checklist should comprise the following:
Getting ready for the Installment
To start with, the sustaining framework supplied with the bathroom must be fitted (if needed) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to avoid stress on the bathtub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its final position.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric prepared for the continuing to be water that will originate from the pipelines. As soon as the supply pipelines have been removed, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. As soon as the faucets have been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing compound.
Before going on to fit the new faucets, compare the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Making use of both wood boards under its feet, put the tub in the required setting. The wood boards are handy in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level and also adjusting the feet on the bath tub until the level reviews degree.
To mount taps, fit the bottom of the furthest versatile tap connector to the suitable supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water supply as well as examine all joints and also brand-new pipework for leaks and tighten them if required. Load the bath tub and likewise inspect the overflow outlet as well as the normal electrical outlet for leakages.
Finally, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the bathtub needs to wait up until the bath tub has actually been used at least when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin guaranteeing that the washing machines remain in area between the tap and also the sink. Safeguard the faucet in place with the producer offered backnut. As soon as the tap is securely in place, the supply pipelines can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The previous type ought to be linked to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bath fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to split a stiff seal, causing the water to penetrate the wall surface between the bath and also the tiling, bring about problems with dampness as well as possible leakages to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are offered in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant sticky and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that write-up on How to Install a Bathtub from someone on another website. If you appreciated our blog posting kindly remember to pass it around. Thank-you for going through it.
24/7 plumbers for emergencies.